Satellite pipelines
===================
The aim of this is to list all possible satellite processing pipelines
as well as their parameters. This does not explain the pipelines by any
means. This should just simplify the CLIs use.
NOAA
----
- ``noaa_hrpt``: NOAA HRPT
- ``noaa_gac``: NOAA GAC
- ``backward``: Over the US, NOAA satellites often transmit in
reverse order. This mode allows decoding those backward replays
properly.
- ``noaa_dsb``: NOAA DSB
- ``noaa_apt``: NOAA APT
- ``satellite_number``: For apt it is required to know what
satellite is being received for projections and overlays. Options
are ``15, 18, 19``
- ``start_timestamp``: Required for projections and overlays. If
your .wav file is a supported format it will be read
automatically. Unix timestamp of the start of the file. Must be
UTC Unix timestamp in seconds.
- ``align_timestamps``: Aligns pass to the correct time using timing
marks in the APT space data. Start time must still be within 15 seconds
for this to work! Default: true
- ``sdrpp_noise_reduction``: Uses the APT noise reduction originally
implemented in SDR++. Default: True
- ``save_unsynced``: Saves the image before it's syncronized. Useful for
weak signals. Default: True
- ``autocrop_wedges``: This will automatically crop the image to
only include telemetry wedges considered valid. May discard a lot
on bad images! Default: False
- ``max_crop_stddev``: If autocropping, the amount of noise to allow at
the top/bottom of the image. Lower values = more cropping. Default:
3500. Useful range is about 400 - 10,000
- ``save_wav``: Saves the wav file. Default: False
Meteor M
--------
- ``meteor_hrpt``: METEOR HRPT
- ``year_override``: Override of the year used for timestamps. Required when you are
processing your file in a different year than the data was created.
- ``meteor_m2_lrpt``: METEOR M2 LRPT 72k
- ``satellite_number``: If specified, overrides automatic satellite dection, and
treats the data as the specified satellite. Valid options: "M2", "M2-2", "M2-3",
or "M2-4".
- ``fill_missing``: Fills in black lines caused by signal drop-outs or interference
- ``max_fill_lines``: Maximum contiguous lines to correct. Default is 50
- ``meteor_m2-x_lrpt``: METEOR M2-X LRPT 72k: Same parameters as meteor_m2_lrpt, plus
- ``rs_usecheck``: Discards data that fails the Reed-Solomon check. True by default,
and it is recommended you leave it on - but you can set it to "false" if the
satellite is transmitting bad RS codes, which may happen from time to time.
- ``meteor_m2-x_lrpt_80k``: METEOR M2-x LRPT 80k (Same parameters as meteor_m2_lrpt)
- ``meteor_m_dump_narrow``: METEOR-M Narrow Dump (WIP!)
- ``meteor_m_dump_wide``: METEOR-M Wide Dump (WIP!)
MetOp
-----
- ``metop_ahrpt``: MetOp AHRPT
- ``write_hpt``: Generate a .hpt file to load into HRPT Reader for
processing.
- ``metop_dump``: MetOp X-Band dump
AIM
---
- ``aim_dump``: AIM dump
AWS
---
- ``aws_pfm``: AWS PFM L-Band (DB and Dump)
- ``use_ephemeris``: Use ephemeris data from the satellite for projection
BlueWalker-3
------------
- ``bluewalker3_wide``: BlueWalker-3 S-Band Wide
- ``bluewalker3_narrow``: BlueWalker-3 S-Band Narrow
Cloudsat
--------
- ``cloudsat_link``: Cloudsat S-Band link
Coriolis
--------
- ``coriolis_db``: Coriolis S-Band Tactical DB
Cosmos
------
- ``cosmos_2558_dump``: Cosmos 2558 S-Band dump
Cryosat
-------
- ``cryosat_dump``: Cryosat X-Band dump
DMSP
----
- ``dmsp_rtd``: DMSP RTD
- ``satellite_number``: DMSP does not transmit a satellite ID. As
instrument configurations do vary between them, it is required to
identify the satellite. Options are ``17, 18``.
EOS
---
- ``aqua_db``: Aqua DB
- ``terra_db``: Terra DB
- ``aura_db``: Aura DB
Elektro / Arktika
-----------------
- ``elektro_rdas``: ELEKTRO-L RDAS
- ``arktika_rdas``: ARKTIKA-M RDAS
- ``elektro_lrit``: ELEKTRO-L LRIT
- ``elektro_hrit``: ELEKTRO-L HRIT
- ``elektro_ggak``: ELEKTRO-L GGAK
- ``arktika_ggak``: ARKTIKA-M GGAK
Fengyun-2
---------
- ``fengyun_svissr``: Fengyun-2 S-VISSR
Fengyun-3
---------
- ``fengyun3_ab_hrpt``: FengYun-3 A/B AHRPT
- ``write_c10``: Generate a .C10 file to load into HRPT Reader for
processing.
- ``fengyun3_c_hrpt``: Fengyun_3 C HRPT
- ``write_c10``: Generate a .C10 file to load into HRPT Reader for
processing.
- ``fengyun3_abc_mpt``: FengYun-3 A/B/C MPT
- ``dump_mersi``: Dump raw MERSI frames for processing with other
software, such as Fred’s WeatherSat!
- ``fengyun3_d_ahrpt``: Fengyun-3 D AHRPT
- ``dump_mersi``: Dump raw MERSI frames for processing with other
software, such as Fred’s WeatherSat!
- ``fengyun3_e_ahrpt``: Fengyun-3 E AHRPT
- ``dump_mersi``: Dump raw MERSI frames for processing with other
software, such as Fred’s WeatherSat!
- ``fengyun3_g_ahrpt``: Fengyun-3 G AHRPT
- ``dump_mersi``: Dump raw MERSI frames for processing with other
software, such as Fred’s WeatherSat!
- ``fengyun3_abc_dpt``: Fengyun-3 A/B/C DPT
- ``dump_mersi``: Dump raw MERSI frames for processing with other
software, such as Fred’s WeatherSat!
- ``fengyun3_d_dpt``: Fengyun-3 D DPT
- ``dump_mersi``: Dump raw MERSI frames for processing with other
software, such as Fred’s WeatherSat!
- ``fengyun3_e_dpt``: Fengyun-3 E DPT
- ``dump_mersi``: Dump raw MERSI frames for processing with other
software, such as Fred’s WeatherSat!
- ``fengyun3_f_ahrpt``: FengYun-3 F AHRPT
- ``dump_mersi``: Dump raw MERSI frames for processing with other
software, such as Fred’s WeatherSat!
- ``fengyun3_tlm_old``: FengYun-3 TLM (Old) A/B/C/D
- ``fengyun3_tlm``: FengYun-3 TLM E/F
-
Fengyun-4
---------
- ``fengyun4_lrit``: Fengyun-4 LRIT
- ``ts_input``: Input TS instead of BBFrame
- ``fengyun4_hrit23``: Fengyun-4 HRIT-II/III
- ``ts_input``: Input TS instead of BBFrame
GCOM
----
- ``gcom_w1_link``: GCOM-W1 link
- ``gcom_c1_link``: GCOM-C1 link
GEO-KOMPSAT_2A (GK-2A)
----------------------
- ``gk2a_lrit``: GK-2A LRIT
- ``gk2a_lrit_tcp``: GK-2A LRIT to xrit-rx
- ``gk2a_hrit``: GK-2A HRIT
- ``gk2a_cdas``: GK-2A CDAS
GOES
----
- ``goes_gvar``: GOES GVAR
- ``goes_hrit``: GOES-R HRIT
- ``write_images``: Saves FD, Meso, etc images (Default: True)
- ``write_emwin``: Save EMWIN Data (Default: True)
- ``write_messages``: Save Admin Messages (Default: True)
- ``write_unknown``: Save Unknown LRIT data(Default: True)
- ``parse_dcs``: Parse DCS files and save as json (Default: False)
- ``tracked_addresses``: When parsing DCS, only save info from the provided
comma-separated addresses (Default: Save all DCS Messages)
- ``write_dcs``: Save DCS LRIT files (Default: False)
- ``write_lrit``: Write all LRIT files (Default: False)
- ``fill_missing``: Corrects black lines caused by interference or signal drop-outs (Default: False)
- ``max_fill_lines``: If ``fill_missing`` is enabled, sets the maximum number of lines that can be filled in (Default: 50)
- ``goes_hrit_tcp``: GOES-R HRIT to goestools
- ``goes_grb``: GOES-R GRB
- ``goesr_cda``: GOES_R CDA
- ``goes_md1``: GOES-N MDL
- ``goes_lrit``: GOES-N LRIT
- ``goesn_cda``: GOES-N CDA
- ``goesn_sounder``: GOES-N Sounder SD
- ``goesn_sd``: GOES-N Sounder Data
- ``goesr_raw``: GOES-R Raw Data
GeoNetCast
----------
- ``geonetcast``: GeoNetCast
- ``ts_input``: Input TS instead of BBFrame
Himawari
--------
- ``himawaricast``: HimawariCast
- ``ts_input``: Input TS instead of BBFrame
Inmarsat
--------
- ``inmarsat_std_c``: Inmarsat STD-C
- ``inmarsat_aero_6``: Inmarsat Aero 0.6k (WIP)
- ``inmarsat_aero_12``: Inmarsat Aero 1.2k (WIP)
- ``inmarsat_aero_84``: Inmarsat Aero 8.4k
- ``inmarsat_aero_105``: Inmarsat Aero 10.5k (WIP)
JPSS
----
- ``npp_hrd``: Suomi NPP / JPSS-1 HRD
- ``jpss_hrd``: JPSS-2/3/4 HRD
- ``jpss_tlm``: JPSS-2/3/4 Telemetry
Jason-3
-------
- ``jason3_link``: Jason-3 S-Band link
Lucky-7
-------
- ``lucky7_link``: Lucky-7 UHF link
MATS
----
- ``mats_dump``: MATS dump
Oceansat
--------
- ``oceansat2_db``: OceanSat-2 DB
- ``oceansat3_argos``: Oceansat-3 L-Band
Orbcomm
-------
- ``orbcomm_stx``: Orbcomm STX
Proba
-----
- ``proba1_dump``: Proba-1 dump
- ``proba2_dump``: Proba-2 dump
- ``probav_s_dump``: Proba-V S-Band dump
- ``probav_x_dump``: Proba-V X-Band dump
SpaceX
------
- ``falcon9_tlm``: Falcon 9 S-Band TLM
- ``starship_tlm``: Starship S-Band TLM
- ``crew_dragon_tlm``: Crew Dragon S-Band TLM
Stereo
------
- ``stereo_lr``: Stereo-A/B Low Rate
- ``stereo_hr``: Stereo-A/B High Rate
TGO
---
- ``tgo_link``: Mars TGO X-Band Link
TUBSAT
------
- ``tubin_x_dump``: TUBIN X-Band Dump
- ``check_crc``: Checks frames for errors. This is usually
desireable, but sometimes ignoring errors may decode a bit more!
UVSQ
----
- ``inspiresat7_tlm``: INSPIRE-Sat7 TLM
UmKA
----
- ``umka_1_dump``: UmKA-1 dump
Others
------
- ``saral_l_band``: Salral L-Band
- ``angels_l_band``: Angels L-Band
- ``gazelle_l_band``: OTB-3/Gazelle L-Band
- ``yunhai_ahrpt``: Yunhai AHRPT - Encrypted ;(
- ``syracuse3b_tlm``: Syracuse 3B TLM
- ``scisat1_dump``: SciSat-1 dump
- ``CALIPSO``: Calipso S-Band dump
- ``youthsat_dump``: YouthSat dump
Chandrayaan
-----------
- ``chandrayaan3_link_1k``: Chandrayaan-3 1k Link
- ``chandrayaan3_link_2k``: Chandrayaan-3 2k Link
- ``chandrayaan3_link_4k``: Chandrayaan-3 4k Link
- ``chandrayaan3_link_8k``: Chandrayaan-3 8k Link
DISCOVR
-------
- ``dscovr_tlm``: DSCOVR TLM Link
- ``dscovr_hr``: DSCOVR High-Rate Link
Hinode
------
- ``hinode_s_dump``: Hinode S-Band Dump
- ``hinode_s_tlm``: Hinode S-Band TLM
Iris
----
- ``iris_s_dump``: IRIS S-Band Dump
- ``iris_dump``: IRIS X-Band Dump
KPLO
----
- ``kplo_sband_link``: KPLO (Danuri) S-Band Link
Landsat
-------
- ``landsat_ldcm_tlm``: LandSat 8/9 S-band
- ``landsat_ldcm_link``: LandSat 8/9 X-band
Orion
-----
- ``orion_link``: Orion S-Band
Sentinel-6
----------
- ``sentinel6_dump``: Sentinel-6 Dump
- ``sentinel6_tlm``: Sentinel 6 S-Band TLM
Tianwen
-------
- ``tianwen1_link``: Tianwen-1 Link
ViaSat
------
- ``viasat3_tlm``: ViaSat-3 TLM
MSG
---
- ``msg_raw``: MSG Raw Data
TODO: add Test, WIP