The aim of this is to list all possible satellite processing pipelines as well as their parameters. This does not explain the pipelines by any means. This should just simplify the CLIs use.

NOAA

noaa_hrpt: NOAA HRPT
noaa_gac: NOAA GAC
- backward: Over the US, NOAA satellites often transmit in reverse order. This mode allows decoding those backward replays properly.
noaa_dsb: NOAA DSB
noaa_apt: NOAA APT
- satellite_number: For apt it is required to know what satellite is being received for projections and overlays. Options are 15, 18, 19
- start_timestamp: Required for projections and overlays. If your .wav file is a supported format it will be read automatically. Unix timestamp of the start of the file. Must be UTC Unix timestamp in seconds.
- align_timestamps: Aligns pass to the correct time using timing marks in the APT space data. Start time must still be within 15 seconds for this to work! Default: true
- sdrpp_noise_reduction: Uses the APT noise reduction originally implemented in SDR++. Default: True
- save_unsynced: Saves the image before it's syncronized. Useful for weak signals or when using narrowband receivers. Default: True
- autocrop_wedges: This will automatically crop the image to only include telemetry wedges considered valid. May discard a lot on bad images! Default: False
- max_crop_stddev: If autocropping, the amount of noise to allow at the top/bottom of the image. Lower values = more cropping. Default: 3500. Useful range is about 400 - 10,000
- save_wav: Saves the wav file. Default: False

Meteor M

meteor_hrpt: METEOR HRPT
- year_override: Override of the year used for timestamps. Required when you are processing your file in a different year than the data was created.
meteor_m2_lrpt: METEOR M2 LRPT 72k
- satellite_number: If specified, overrides automatic satellite dection, and treats the data as the specified satellite. Valid options: "M2", "M2-2", "M2-3", or "M2-4".
- fill_missing: Fills in black lines caused by signal drop-outs or interference
- max_fill_lines: Maximum contiguous lines to correct. Default is 50
meteor_m2-x_lrpt: METEOR M2-X LRPT 72k: Same parameters as meteor_m2_lrpt, plus
- rs_usecheck: Discards data that fails the Reed-Solomon check. True by default, and it is recommended you leave it on, but you can set it to "false" if the satellite is transmitting bad RS codes, which may happen from time to time.
meteor_m2-x_lrpt_80k: METEOR M2-x LRPT 80k (Same parameters as meteor_m2_lrpt)
meteor_m_dump_narrow: METEOR-M Narrow Dump (WIP!)
meteor_m_dump_wide: METEOR-M Wide Dump (WIP!)

MetOp

metop_ahrpt: MetOp AHRPT
- write_hpt: Generate a .hpt file to load into HRPT Reader for processing.
metop_dump: MetOp X-Band dump

AIM

aim_dump: AIM dump

AWS

aws_pfm: AWS PFM L-Band (DB and Dump)
- use_ephemeris: Use ephemeris data from the satellite for projection

BlueWalker-3

bluewalker3_wide: BlueWalker-3 S-Band Wide
bluewalker3_narrow: BlueWalker-3 S-Band Narrow

Cloudsat

cloudsat_link: Cloudsat S-Band link

Coriolis

coriolis_db: Coriolis S-Band Tactical DB

Cosmos

cosmos_2558_dump: Cosmos 2558 S-Band dump

Cryosat

cryosat_dump: Cryosat X-Band dump

DMSP

dmsp_rtd: DMSP RTD
- satellite_number: DMSP does not transmit a satellite ID. As instrument configurations do vary between them, it is required to identify the satellite. Options are 17, 18.

EOS

aqua_db: Aqua DB
terra_db: Terra DB
aura_db: Aura DB

Elektro / Arktika

elektro_rdas: ELEKTRO-L RDAS
arktika_rdas: ARKTIKA-M RDAS
elektro_lrit: ELEKTRO-L LRIT
elektro_hrit: ELEKTRO-L HRIT
elektro_ggak: ELEKTRO-L GGAK
arktika_ggak: ARKTIKA-M GGAK

Fengyun-2

fengyun_svissr: Fengyun-2 S-VISSR

Fengyun-3

fengyun3_ab_hrpt: FengYun-3 A/B AHRPT
- write_c10: Generate a .C10 file to load into HRPT Reader for processing.
fengyun3_c_hrpt: Fengyun_3 C HRPT
- write_c10: Generate a .C10 file to load into HRPT Reader for processing.
fengyun3_abc_mpt: FengYun-3 A/B/C MPT
- dump_mersi: Dump raw MERSI frames for processing with other software, such as Fred's WeatherSat!
- mersi_histmatch: Toggle line-based histogram equalization for MERSI, to make the image smoother. However, this causes problems with thunderstorm clouds appearing too white. .
fengyun3_d_ahrpt: Fengyun-3 D AHRPT
- dump_mersi: Dump raw MERSI frames for processing with other software, such as Fred's WeatherSat!
- mersi_histmatch: Toggle line-based histogram equalization for MERSI, to make the image smoother. However, this causes problems with thunderstorm clouds appearing too white.
fengyun3_e_ahrpt: Fengyun-3 E AHRPT
- dump_mersi: Dump raw MERSI frames for processing with other software, such as Fred's WeatherSat!
- mersi_histmatch: Toggle line-based histogram equalization for MERSI, to make the image smoother. However, this causes problems with thunderstorm clouds appearing too white.
fengyun3_g_ahrpt: Fengyun-3 G AHRPT
- dump_mersi: Dump raw MERSI frames for processing with other software, such as Fred's WeatherSat!
- mersi_histmatch: Toggle line-based histogram equalization for MERSI, to make the image smoother. However, this causes problems with thunderstorm clouds appearing too white.
fengyun3_abc_dpt: Fengyun-3 A/B/C DPT
- dump_mersi: Dump raw MERSI frames for processing with other software, such as Fred's WeatherSat!
- mersi_histmatch: Toggle line-based histogram equalization for MERSI, to make the image smoother. However, this causes problems with thunderstorm clouds appearing too white.
fengyun3_d_dpt: Fengyun-3 D DPT
- dump_mersi: Dump raw MERSI frames for processing with other software, such as Fred's WeatherSat!
- mersi_histmatch: Toggle line-based histogram equalization for MERSI, to make the image smoother. However, this causes problems with thunderstorm clouds appearing too white.
fengyun3_e_dpt: Fengyun-3 E DPT
- dump_mersi: Dump raw MERSI frames for processing with other software, such as Fred's WeatherSat!
- mersi_histmatch: Toggle line-based histogram equalization for MERSI, to make the image smoother. However, this causes problems with thunderstorm clouds appearing too white.
fengyun3_f_ahrpt: FengYun-3 F AHRPT
- dump_mersi: Dump raw MERSI frames for processing with other software, such as Fred's WeatherSat!
- mersi_histmatch: Toggle line-based histogram equalization for MERSI, to make the image smoother. However, this causes problems with thunderstorm clouds appearing too white.
fengyun3_tlm_old: FengYun-3 TLM (Old) A/B/C/D
fengyun3_tlm: FengYun-3 TLM E/F

Fengyun-4

fengyun4_lrit: Fengyun-4 LRIT
- ts_input: Input TS instead of BBFrame
fengyun4_hrit23: Fengyun-4 HRIT-II/III
- ts_input: Input TS instead of BBFrame

GCOM

gcom_w1_link: GCOM-W1 link
gcom_c1_link: GCOM-C1 link

GEO-KOMPSAT_2A (GK-2A)

gk2a_lrit: GK-2A LRIT
gk2a_lrit_tcp: GK-2A LRIT to xrit-rx
gk2a_hrit: GK-2A HRIT
gk2a_cdas: GK-2A CDAS

GOES

goes_gvar: GOES GVAR
goes_hrit: GOES-R HRIT
- write_images: Saves FD, Meso, etc images (Default: True)
- write_emwin: Save EMWIN Data (Default: True)
- write_messages: Save Admin Messages (Default: True)
- write_unknown: Save Unknown LRIT data(Default: True)
- parse_dcs: Parse DCS files and save as json (Default: False)
- tracked_addresses: When parsing DCS, only save info from the provided comma-separated addresses (Default: Save all DCS Messages)
- write_dcs: Save DCS LRIT files (Default: False)
- write_lrit: Write all LRIT files (Default: False)
- fill_missing: Corrects black lines caused by interference or signal drop-outs (Default: False)
- max_fill_lines: If fill_missing is enabled, sets the maximum number of lines that can be filled in (Default: 50)
goes_hrit_tcp: GOES-R HRIT to goestools
goes_grb: GOES-R GRB
goesr_cda: GOES_R CDA
goes_md1: GOES-N MDL
goes_lrit: GOES-N LRIT
goesn_cda: GOES-N CDA
goesn_sounder: GOES-N Sounder SD
goesn_sd: GOES-N Sounder Data
goesr_raw: GOES-R Raw Data

GeoNetCast

geonetcast: GeoNetCast
- ts_input: Input TS instead of BBFrame

Himawari

himawaricast: HimawariCast
- ts_input: Input TS instead of BBFrame

Inmarsat

inmarsat_std_c: Inmarsat STD-C
inmarsat_aero_6: Inmarsat Aero 0.6k (WIP)
inmarsat_aero_12: Inmarsat Aero 1.2k (WIP)
inmarsat_aero_84: Inmarsat Aero 8.4k
inmarsat_aero_105: Inmarsat Aero 10.5k (WIP)

JPSS

npp_hrd: Suomi NPP / JPSS-1 HRD
jpss_hrd: JPSS-2/3/4 HRD
jpss_tlm: JPSS-2/3/4 Telemetry

Jason-3

jason3_link: Jason-3 S-Band link

Lucky-7

lucky7_link: Lucky-7 UHF link

MATS

mats_dump: MATS dump

Oceansat

oceansat2_db: OceanSat-2 DB
oceansat3_argos: Oceansat-3 L-Band

Orbcomm

orbcomm_stx: Orbcomm STX

Proba

proba1_dump: Proba-1 dump
proba2_dump: Proba-2 dump
probav_s_dump: Proba-V S-Band dump
probav_x_dump: Proba-V X-Band dump

SpaceX

falcon9_tlm: Falcon 9 S-Band TLM
starship_tlm: Starship S-Band TLM
crew_dragon_tlm: Crew Dragon S-Band TLM

Stereo

stereo_lr: Stereo-A/B Low Rate
stereo_hr: Stereo-A/B High Rate

TGO

tgo_link: Mars TGO X-Band Link

TUBSAT

tubin_x_dump: TUBIN X-Band Dump
- check_crc: Checks frames for errors. This is usually desireable, but sometimes ignoring errors may decode a bit more!

UVSQ

inspiresat7_tlm: INSPIRE-Sat7 TLM

UmKA

umka_1_dump: UmKA-1 dump

Others

saral_l_band: Salral L-Band
angels_l_band: Angels L-Band
gazelle_l_band: OTB-3/Gazelle L-Band
yunhai_ahrpt: Yunhai AHRPT. Encrypted ;(
syracuse3b_tlm: Syracuse 3B TLM
scisat1_dump: SciSat-1 dump
CALIPSO: Calipso S-Band dump
youthsat_dump: YouthSat dump

Chandrayaan

chandrayaan3_link_1k: Chandrayaan-3 1k Link
chandrayaan3_link_2k: Chandrayaan-3 2k Link
chandrayaan3_link_4k: Chandrayaan-3 4k Link
chandrayaan3_link_8k: Chandrayaan-3 8k Link

DISCOVR

dscovr_tlm: DSCOVR TLM Link
dscovr_hr: DSCOVR High-Rate Link

Hinode

hinode_s_dump: Hinode S-Band Dump
hinode_s_tlm: Hinode S-Band TLM

Iris

iris_s_dump: IRIS S-Band Dump
iris_dump: IRIS X-Band Dump

KPLO

kplo_sband_link: KPLO (Danuri) S-Band Link

Landsat

landsat_ldcm_tlm: LandSat 8/9 S-band
landsat_ldcm_link: LandSat 8/9 X-band

Orion

orion_link: Orion S-Band

Sentinel-6

sentinel6_dump: Sentinel-6 Dump
sentinel6_tlm: Sentinel 6 S-Band TLM

Tianwen

tianwen1_link: Tianwen-1 Link

ViaSat

viasat3_tlm: ViaSat-3 TLM

MSG

msg_raw: MSG Raw Data

TODO: add Test, WIP