Satellite pipelines

The aim of this is to list all possible satellite processing pipelines as well as their parameters. This does not explain the pipelines by any means. This should just simplify the CLIs use.

NOAA

  • noaa_hrpt: NOAA HRPT

  • noaa_gac: NOAA GAC

    • backward: Over the US, NOAA satellites often transmit in reverse order. This mode allows decoding those backward replays properly.

  • noaa_dsb: NOAA DSB

  • noaa_apt: NOAA APT

    • satellite_number: For apt it is required to know what satellite is being received for projections and overlays. Options are 15, 18, 19

    • start_timestamp: Required for projections and overlays. If your .wav file is a supported format it will be read automatically. Unix timestamp of the start of the file. Must be UTC Unix timestamp in seconds.

    • align_timestamps: Aligns pass to the correct time using timing marks in the APT space data. Start time must still be within 15 seconds for this to work! Default: true

    • sdrpp_noise_reduction: Uses the APT noise reduction originally implemented in SDR++. Default: True

    • save_unsynced: Saves the image before it’s syncronized. Useful for weak signals. Default: True

    • autocrop_wedges: This will automatically crop the image to only include telemetry wedges considered valid. May discard a lot on bad images! Default: False

    • max_crop_stddev: If autocropping, the amount of noise to allow at the top/bottom of the image. Lower values = more cropping. Default: 3500. Useful range is about 400 - 10,000

    • save_wav: Saves the wav file. Default: False

Meteor M

  • meteor_hrpt: METEOR HRPT

    • start_timestamp: Unix timestamp of the start of the file provided. Must be UTC Unix timestamp in seconds.Required in case you are not processing your file on the same Moscow day.

  • meteor_m2_lrpt: METEOR M2 LRPT 72k

    • satellite_number: If specified, overrides automatic satellite dection, and treats the data as the specified satellite. Valid options: “M2”, “M2-2”, “M2-3”, or “M2-4”.

    • fill_missing: Fills in black lines caused by signal drop-outs or interference

    • max_fill_lines: Maximum contiguous lines to correct. Default is 50

  • meteor_m2-x_lrpt: METEOR M2-X LRPT 72k: Same parameters as meteor_m2_lrpt, plus

    • rs_usecheck: Discards data that fails the Reed-Solomon check. True by default, and it is recommended you leave it on - but you can set it to “false” if the satellite is transmitting bad RS codes, which may happen from time to time.

  • meteor_m2-x_lrpt_80k: METEOR M2-x LRPT 80k (Same parameters as meteor_m2_lrpt)

  • meteor_m_dump_narrow: METEOR-M Narrow Dump (WIP!)

  • meteor_m_dump_wide: METEOR-M Wide Dump (WIP!)

MetOp

  • metop_ahrpt: MetOp AHRPT

    • write_hpt: Generate a .hpt file to load into HRPT Reader for processing.

  • metop_dump: MetOp X-Band dump

AIM

  • aim_dump: AIM dump

BlueWalker-3

  • bluewalker3_wide: BlueWalker-3 S-Band Wide

  • bluewalker3_narrow: BlueWalker-3 S-Band Narrow

Cloudsat

  • cloudsat_link: Cloudsat S-Band link

Coriolis

  • coriolis_db: Coriolis S-Band Tactical DB

Cosmos

  • cosmos_2558_dump: Cosmos 2558 S-Band dump

Cryosat

  • cryosat_dump: Cryosat X-Band dump

DMSP

  • dmsp_rtd: DMSP RTD

    • satellite_number: DMSP does not transmit a satellite ID. As instrument configurations do vary between them, it is required to identify the satellite. Options are 17, 18.

EOS

  • aqua_db: Aqua DB

  • terra_db: Terra DB

  • aura_db: Aura DB

Elektro / Arktika

  • elektro_rdas: ELEKTRO-L RDAS

  • arktika_rdas: ARKTIKA-M RDAS

  • elektro_lrit: ELEKTRO_L LRIT

  • elektro_hrit: ELEKTRO_L HRIT

  • elektro_tlm: ELEKTRO_L TLM

  • arktika_tlm: ARKTIKA-M L-Band TLM

Fengyun-2

  • fengyun_svissr: Fengyun-2 S-VISSR

Fengyun-3

  • fengyun3_ab_hrpt: FengYun-3 A/B AHRPT

    • write_c10: Generate a .C10 file to load into HRPT Reader for processing.

  • fengyun3_c_hrpt: Fengyun_3 C HRPT

    • write_c10: Generate a .C10 file to load into HRPT Reader for processing.

  • fengyun3_abc_mpt: FengYun-3 A/B/C MPT

    • dump_mersi: Dump raw MERSI frames for processing with other software, such as Fred’s WeatherSat!

  • fengyun3_d_ahrpt: Fengyun-3 D AHRPT

    • dump_mersi: Dump raw MERSI frames for processing with other software, such as Fred’s WeatherSat!

  • fengyun3_e_ahrpt: Fengyun-3 E AHRPT

    • dump_mersi: Dump raw MERSI frames for processing with other software, such as Fred’s WeatherSat!

  • fengyun3_g_ahrpt: Fengyun-3 G AHRPT

    • dump_mersi: Dump raw MERSI frames for processing with other software, such as Fred’s WeatherSat!

  • fengyun3_abc_dpt: Fengyun-3 A/B/C DPT

    • dump_mersi: Dump raw MERSI frames for processing with other software, such as Fred’s WeatherSat!

  • fengyun3_d_dpt: Fengyun-3 D DPT

    • dump_mersi: Dump raw MERSI frames for processing with other software, such as Fred’s WeatherSat!

  • fengyun3_e_dpt: Fengyun-3 E DPT

    • dump_mersi: Dump raw MERSI frames for processing with other software, such as Fred’s WeatherSat!

  • fengyun3_f_ahrpt: FengYun-3 F AHRPT

    • dump_mersi: Dump raw MERSI frames for processing with other software, such as Fred’s WeatherSat!

  • fengyun3_tlm_old: FengYun-3 TLM (Old) A/B/C/D

  • fengyun3_tlm: FengYun-3 TLM E/F

Fengyun-4

  • fengyun4_lrit: Fengyun-4 LRIT

    • ts_input: Input TS instead of BBFrame

  • fengyun4_hrit23: Fengyun-4 HRIT-II/III

    • ts_input: Input TS instead of BBFrame

GCOM

  • gcom_w1_link: GCOM-W1 link

  • gcom_c1_link: GCOM-C1 link

GEO-KOMPSAT_2A (GK-2A)

  • gk2a_lrit: GK-2A LRIT

  • gk2a_lrit_tcp: GK-2A LRIT to xrit-rx

  • gk2a_hrit: GK-2A HRIT

  • gk2a_cdas: GK-2A CDAS

GOES

  • goes_gvar: GOES GVAR

  • goes_hrit: GOES-R HRIT

    • write_images: Saves FD, Meso, etc images (Default: True)

    • write_emwin: Save EMWIN Data (Default: True)

    • write_messages: Save Admin Messages (Default: True)

    • write_unknown: Save Unknown LRIT data(Default: True)

    • write_dcs: Save DCS LRIT files (Default: False)

    • write_lrit: Write all LRIT files (Default: False)

    • fill_missing: Corrects black lines caused by interference or signal drop-outs (Default: False)

    • max_fill_lines: If fill_missing is enabled, sets the maximum number of lines that can be filled in (Default: 50)

  • goes_hrit_tcp: GOES-R HRIT to goestools

  • goes_grb: GOES-R GRB

  • goesr_cda: GOES_R CDA

  • goes_md1: GOES-N MDL

  • goes_lrit: GOES-N LRIT

  • goesn_cda: GOES-N CDA

  • goesn_sounder: GOES-N Sounder SD

  • goesn_sd: GOES-N Sounder Data

  • goesr_raw: GOES-R Raw Data

GeoNetCast

  • geonetcast: GeoNetCast

    • ts_input: Input TS instead of BBFrame

Himawari

  • himawaricast: HimawariCast

    • ts_input: Input TS instead of BBFrame

Inmarsat

  • inmarsat_std_c: Inmarsat STD-C

  • inmarsat_aero_6: Inmarsat Aero 0.6k (WIP)

  • inmarsat_aero_12: Inmarsat Aero 1.2k (WIP)

  • inmarsat_aero_84: Inmarsat Aero 8.4k

  • inmarsat_aero_105: Inmarsat Aero 10.5k (WIP)

JPSS

  • npp_hrd: Suomi NPP / JPSS-1 HRD

  • jpss_hrd: JPSS-2/3/4 HRD

  • jpss_tlm: JPSS-2/3/4 Telemetry

Jason-3

  • jason3_link: Jason-3 S-Band link

Lucky-7

  • lucky7_link: Lucky-7 UHF link

MATS

  • mats_dump: MATS dump

Oceansat

  • oceansat2_db: OceanSat-2 DB

  • oceansat3_argos: Oceansat-3 L-Band

Orbcomm

  • orbcomm_stx: Orbcomm STX

Proba

  • proba1_dump: Proba-1 dump

  • proba2_dump: Proba-2 dump

  • probav_s_dump: Proba-V S-Band dump

  • probav_x_dump: Proba-V X-Band dump

SpaceX

  • falcon9_tlm: Falcon 9 S-Band TLM

  • starship_tlm: Starship S-Band TLM

  • crew_dragon_tlm: Crew Dragon S-Band TLM

Stereo

  • stereo_lr: Stereo-A/B Low Rate

  • stereo_hr: Stereo-A/B High Rate

TGO

  • tgo_link: Mars TGO X-Band Link

TUBSAT

  • tubin_x_dump: TUBIN X-Band Dump

    • check_crc: Checks frames for errors. This is usually desireable, but sometimes ignoring errors may decode a bit more!

UVSQ

  • inspiresat7_tlm: INSPIRE-Sat7 TLM

UmKA

  • umka_1_dump: UmKA-1 dump

Others

  • saral_l_band: Salral L-Band

  • angels_l_band: Angels L-Band

  • gazelle_l_band: OTB-3/Gazelle L-Band

  • yunhai_ahrpt: Yunhai AHRPT - Encrypted ;(

  • syracuse3b_tlm: Syracuse 3B TLM

  • scisat1_dump: SciSat-1 dump

  • CALIPSO: Calipso S-Band dump

  • youthsat_dump: YouthSat dump

Chandrayaan

  • chandrayaan3_link_1k: Chandrayaan-3 1k Link

  • chandrayaan3_link_2k: Chandrayaan-3 2k Link

  • chandrayaan3_link_4k: Chandrayaan-3 4k Link

  • chandrayaan3_link_8k: Chandrayaan-3 8k Link

DISCOVR

  • dscovr_tlm: DSCOVR TLM Link

  • dscovr_hr: DSCOVR High-Rate Link

Hinode

  • hinode_s_dump: Hinode S-Band Dump

  • hinode_s_tlm: Hinode S-Band TLM

Iris

  • iris_s_dump: IRIS S-Band Dump

  • iris_dump: IRIS X-Band Dump

KPLO

  • kplo_sband_link: KPLO (Danuri) S-Band Link

Landsat

  • landsat_ldcm_tlm: LandSat 8/9 S-band

  • landsat_ldcm_link: LandSat 8/9 X-band

Orion

  • orion_link: Orion S-Band

Sentinel-6

  • sentinel6_dump: Sentinel-6 Dump

  • sentinel6_tlm: Sentinel 6 S-Band TLM

Tianwen

  • tianwen1_link: Tianwen-1 Link

ViaSat

  • viasat3_tlm: ViaSat-3 TLM

MSG

  • msg_raw: MSG Raw Data

TODO: add Test, WIP